Four years on…

And Casa Chica is still my permanent residence! Mostly. I was working full-time in Minneapolis for a spell in 2019 and signed a year lease on an apartment, so I decided to shut down the little house for the winter. It’s too hard (on my nerves) to make sure it stays warm enough if I’m not there mostly full time. So last fall I drained all the water (hopefully, we’ll find out in spring), added some anti-freeze, removed any consumables that shouldn’t freeze and shut the door. I check on it from time to time, and all is well. I miss it, but it is awfully nice living in a place where the water comes out of the tap without any more effort from me than a flip of the faucet handle and I don’t have to clean toilet buckets in below zero weather. I’m getting soft as I approach 50. But the hardest thing about living in Casa Chica is living in it in the winter. I haven’t had condensation problems that I’ve heard horror stories about, but I designed with that in mind (like with the passive air inlet) and have employed other solutions like running a dehumidifier on really cold nights to minimize the ice buildup on the inside of the windows.

I’m also happy to report that Casa Chica successfully moved over the road to her current  location! It was only a couple of miles, but we had to go up a very steep hill and I’ve no idea how much she weighs so we borrowed the biggest truck we could find (a full ton, I think, and it was struggling up the hill). I was nervous, but she did great!

Technically it’s still not finished. This fall I finally got the shower completed, minus hanging the shower curtain, although I’ve yet to try it out (but yes, I have showered in the past 4 years. Gyms and friends, or a garden hose in the summer). It’s still waiting on some interior trim, there still aren’t doors for the storage attics, and I never did give all of the interior wood walls a clear coat. That’s all coming. But as an update to my last post in September 2015:

• The exterior is stained! See photos. I used Bioshield Resin and Oil Stain Finish #3. My friend Andrea had to talk me into the two-tone, but now I love it. I had it professionally done and the painter had never used it before so he sprayed it on. This summer was particularly harsh to the stain on the southwest facing side so I put on another coat of blue and will probably have to do some work on the orange/red side next year. I think it needs to be applied thicker than the spray was able to achieve. I also had all the mis-matched window frames painted a dark brown to match the color that came on the front door.
• All water features work, and over the first few months of living in the house I developed a system for filling the fresh water tank and emptying the gray water tank (hint: do it at the same time, or run the risk of the gray water tank backing up into the shower). For the first two summers I kept the water hose connected to the house for on-demand water without having to fill a tank, but the hoses were out in the sun and got GROSS. And cleaning them was a pain. So for the past couple of years I’ve filled the water tank year-round, about once a week (without a shower). Not that big of a deal, but tricky in the winter. I’ve found it has to be above about 20F (and I have to move fast) to be able to keep the hoses from freezing so quickly they block the flow. I’m not super impressed with my PrecisionTemp RV-550 tankless water heater – it’s not exactly instantaneous so I try to collect the cold water while I wait for the hot – but I’m not sure what I would replace it with. And I did end up getting a small Flojet diaphragm pump that works great. It’s a bit noisy, but I’m used to it.
• I found that the cheapo (relatively) LED bulbs that came with my Home Depot can lights worked without buzzing, so that’s what I put in my track lights as well. I also learned that you can’t have dimmers on two switches on the same circuit. I got a seizure-inducing (not really) light show.
• All of the shelves and built-ins have been in since not too long after I moved in. That’s truly what makes the house 100% livable even though it’s 90% finished. Also in a long time ago is the 2-burner Ramblewood GC2-43P propane stove (love it, no complaints). I have a Broan Allure stove hood (I don’t think it’s made anymore) that doesn’t work as well as I’d like it to, but I think it’s a function of being too high above the stove than an equipment malfunction. There’s a window behind the stove so I didn’t have much choice on putting the hood lower. And I’ve learned that I can’t have the hood on high at the same time I have a fire going in the wood stove or I’ll fill the house up with smoke lickety split.
• Also in is the gorgeous cork flooring. I think everyone who has been on the house has commented on it first. I bought it through a green home designer/supplier in the Twin Cities that has since been bought out so I’ve no idea where to get it anymore. I haven’t washed the whole floor in the four years it’s been there (I take my shoes off at the door and spot wipe spills/water), and you can’t tell by looking. And it adds such character to the look of the place.
• I’ve been using my Kimberly wood stove every winter since I moved in, and I’ll be honest in saying it hasn’t been an easy road to loving it as I do now. A very large part of the problem (maybe all of it) was that I bought any-old-pellet-stove-pipe locally rather than the brand that Unforgettable Fire recommended, and it turns out that it’s not sealed as well as it needs to be for the stove to burn super efficiently. The dealer from whom I bought the stove, Vanessa at Eagle Rise Trading Company, has gone over the top in helping me troubleshoot via detailed emails, phone calls, and even a trip to Wisconsin to spend a long afternoon doing everything she could to “upgrade” the seals on the stove itself (mine was an earlier iteration) and check my installation (with live phone advice from Roger, the stove’s inventor and CEO of Unforgettable Fire). She also convinced me that I needed to replace the chimney pipe, which I did in 2018, and the stove worked like a champ last winter. I’ve also learned to use compressed sawdust logs when I want a long overnight burn, and with that I can wake up to coals 8 hours after I fed the stove before bed. Plus, it’s still so damn charming, especially with my custom metal hearth pad…

And what would I do differently? Not much, but:

• #1 for sure – I’d install a secondary source of heat that would keep the place warm when I’m not there, probably propane, like a Williams High Efficiency Direct Vent Furnace. Right now my backup heat is a plug-in electric heater, which is not very efficient or reliable. If the power goes out, so does my heater, and it doesn’t come back on (hence my reluctance to try to heat the house with it if I’m not there most of the time). I’ve tried an oil-filled electric radiator too, but the one I bought doesn’t have a thermostat so it’s really hard to know where to set it (again, hence my reluctance…) and it doesn’t heat the whole space as well without a blower (yes, I could use a fan, but geez). I could put in cheap baseboard electric, but I still want to leave the off-grid solar option open. So propane. I can still install a direct-vent furnace and may next summer, but it would have been a lot easier if we’d done it while the house was being built.
• I also may have given more consideration to installing a mini split system. It would be an efficient source of backup heat as well as a welcome splash of air conditioning on the few days a year it would be nice to have. It’s still not sufficient to get me through the coldest days of winter – the lowest temperature rating for any I’ve seen is -5F, and we can go into the -20s or even -30s – so I’d still need another backup heater.
• I’d put another outlet on the wall opposite my bed.

Onward and upward! And I’m looking forward to filling the tank and throwing open the windows this spring, and spending more of my nights sleeping in my tiny house.

The two-tone Casa Chica, at her new home!

A fisheye view of the kitchen and bathroom from the “living” room.

A fisheye view of the “living” room and bedroom. Note the Kimberly wood stove and custom metal hearth.

The bathroom built-in. Shower is to the right, toilet is to the left.

My kitchen sink area. The hot water heater is under the sink.

My house on wheels!

I love these built-ins. Tons of storage!

 

Advertisement

Consistent progress, inconsistent blogging…

The fact that I haven’t posted anything in, what, 6 months, does not in fact mean that Casa Chica has sat idle and un-worked-on since she moved out of the shed. On the contrary! The biggest news is – she’s unfinished, but occupied! By me! Since just before Memorial Day. We also moved her to her “permanent” location and have made serious progress on the interior, although gardening and haymaking and other summer farm activities have slowed things down somewhat. But still, she’s now a home.

I’m going through my photo album to determine the order of things. A rapid update on progress requires a bulleted list, so here’s what’s been done since March:

• Exterior: Installed soffits and soffit vents, and the battens and all of the window and door trim are on. We still haven’t stained the outside, but the Seal Once waterproofer seems to be holding its own. Even in the remarkably wet weather we’ve been having lately, including a 5+-inch deluge a few weeks ago.
• The fresh water tank and water pump are installed and plumbed, but I don’t have sinks or a shower yet. I have all the necessary equipment and accouterments though, in boxes taking up half of the bathroom. Including the hot water heater – after reading some posts from other tiny housers who have one, I decided to go with the PrecisionTemp RV-550 tankless water heater. I had initially planned to get a small electric water heater, but the electricity vampirism kept niggling at me, since I am loosely trying to keep possible future solar panels in mind. And six gallons of hot water ain’t much; I didn’t go tiny to go Navy.
• Wiring is finished, so I have electricity. I have 50 amp service on a pole, and will eventually have my own meter so I know how much of the farm electricity bill is mine. Recessed lights in the bedroom and bathroom are all in, and enough track lights in the living room/kitchen to be able to function. Finding LED bulbs that don’t buzz (a persistent problem with LED lights on dimmers, I’m told) is the hold-up. The lovely and expensive SORAA bulbs I originally bought buzz like a beehive. I’m having better luck with cheaper bulbs but haven’t settled on one yet. And we’ve been having some hot weather of late so I hauled the ceiling fan out of the box and installed it. I bought a Wave by Minka Aire, in distressed koa finish to go with the other dark wood accents we have going on.
• Many of the built-ins are in! The installation of the bed and bedroom drawers was what allowed me to move in officially, followed by bedside tables, entryway and sitting area cabinets. Lower kitchen cabinets and counter top are the latest additions. And man-oh-man is everything beautiful! Maple with a natural finish, with black walnut tops and accents. The kitchen counter top is a laminate. I have more than enough drawers for all my clothes, more space in the six storage areas under the bed than I have stuff to put in them, and in general far more storage than I thought possible in such a small house. My brilliant designer friend (Andrea) and my artist of a cabinet maker (Scott) are having so much fun maximizing space (with my input, but the details make my head explode. I’m mostly the final approval authority with the checkbook). The built-ins are officially pushing this project into the “high budget tiny house” category (if there is such a thing), but for me it’s worth it. Building tiny is allowing me to be able to afford far higher quality materials, fixtures and finishes than I would if I were building a normal-sized house, even a small one.
• I also have refrigeration. I bought a Danby 4.4 cu refrigerator because of its relatively good energy efficiency. I loved the space in the refrigerator and the somewhat useful can storage (you can’t get a compact refrigerator without can storage in the door, which I find to be an almost completely useless space since I don’t do canned drinks), but decided I couldn’t live with the teeny-tiny freezer that wouldn’t even hold a pint of ice cream without squishing it in on its side. So I replaced the Danby with the EdgeStar 3.1 cu refrigerator/freezer that Tumbleweed recommends. Much smaller refrigerator space but much improved freezer space for me. And it’s still pretty energy efficient for a compact refrigerator.

Up next: the open shelves in the kitchen and the bathroom built-ins are in the works. I may have running water in the next couple of weeks hooray, and a working stove! The cork floor installation is fixing to happen. And the metal hearth pad an artist friend made for underneath my wood stove will deserve a post of its own once it’s installed.

Casa Chica in her “permanent” location! With her not-so-permanent front steps. Definitely not to code.

My bed platform! I have to move/lift the mattress to access the storage, so it’s for things like seasonal clothes and extra bedding.

Bedroom drawers, and one of the bedside tables. Almost more drawers than I need.

Minka-Aire Wave fan. Stylish and wayyyy functional.

This is what we’re calling the “hanging chair unit.”

The sink side of the kitchen cabinets. The missing drawer is getting dividers put in it. I’ve been using my camp stove since I moved in, hopefully not much longer!

The stove side of the kitchen cabinets, with the seating area. There will be a couple of stools under that overhang. I love the little cubbies for my TV and other things I don’t want out on permanent display.

The solution for the corner was a bunch of shelves rather than an awkward cupboard.

My little refrigerator.

Out in the sunlight!

OK, so I’ve mentioned before that we wanted to get Casa Chica out of the shed she’s being built in. The shed was a totally perfect incubator – it protected her vulnerable bits from rain and snow, allowed Mike to work in all weather, and saved hours of time of tarping and un-tarping that would have been required had she been outside (not to mention saving the cost of the tarps). But she had outgrown it, literally – Mike would have had to put on the ridge cap while lying on his belly and risk putting the hammer claw through the roof. So out she needed to go. But we had missed the window in the fall of weather warm enough to put any protectant on the outside, and even though the plywood is exterior grade we weren’t sure how much we wanted to test its durability through spring rains/late snowstorms. One can’t usually count on early March being warm enough to paint or stain, which was a moot point anyway because we still haven’t decided on paint vs stain, let alone colors. But! We got extremely lucky this year with an early warm-up – 50s and 60s for days on end! When I saw that forecast I was motivated to figure out some way to protect Casa Chica’s exterior so we could get her outside with some peace of mind, but without having to make any seat-of-my-pants decisions on exterior finishes. Surely someone makes a stainable/paintable wood protectant, one that doesn’t require major respiratory protection to apply or, if spilled, create a Superfund site? Yes indeedy, enter Seal-Once! Stainable/paintable, water-based, low/no VOCs, no heavy metals or other toxins. Nanomaterials yes (we took to calling them nanobots), and while there’s very little known about the health effects of nanobots, given the non-toxicity of the rest of the ingredients I felt the risk of it causing any problems is low (I’m an industrial hygienist, so I know more than a smidge about health risk assessments). There’s a dearth of information about Seal-Once on the interwebs outside of manufacturer propaganda, but I found a couple of positive reviews so I took a leap of faith and ordered a 5-gallon bucket of this magic material, enough (and then some, as it turned out) for two coats.

It arrived in the 2 days promised by Amazon Prime, and the forecast was still looking good to get it on while temps were above 35F per the instructions. Mike, bless him, spent last Thursday sanding the entire exterior, which needed to be done sooner or later because the plywood we chose was a bit “fuzzy.” And on Friday I was able to help with the application of the Seal-Once for a little bit before I had to run off to work. It’s interesting stuff – looks a bit like I bought a 5-gallon bucket of expensive skim milk. We used paint pads to apply it and the watery-ness required some trial and error to get most of it on the house and less on the toes, but once mastered it was a pretty easy job. We applied one coat to one side of the house, then went right over it with the second coat before moving on to the next side. We both noted the very faint chemical smell, but nothing that even approached being even slightly unpleasant to work in. It dried pretty quickly – to the touch in a couple of hours – and maybe evened out the color of the wood a bit, and it looks for all the world like it will be paintable/stainable later. So far I’m pleased with the decision to put it on! No idea how well it works of course, but we’re fixin’ to test it. I’ll report observations later. Rain is forecasted for Monday.

We let Casa Chica dry in the shed completely overnight before moving her out on Saturday morning. We’re not really sure how much she weighs or how much of the weight is on the trailer tongue, but we figured we’d try the farm’s full-ton truck with the heavy-duty shocks and springs first and, if that was a no-go, get out the tractor. No need for the tractor. She lowered onto the truck’s hitch beautifully, and, after trimming a couple of branches on the tree some yayhoo had planted right in front of the shed about 25 years ago, out she came! Narry a wobble or otherwise scary moment! Perhaps my concerns about my cheap, narrow old RV trailer frame not being up to the task are unfounded. She didn’t move far – maybe 75 feet – and the new location is only temporary (her “permanent” resting place is down a hill and on ground that is still waterlogged, so that move will come later), but it was a blissfully uneventful event. Yet still exciting, because it feels like a big step in her construction. We spent an hour or so getting the RV jacks back in place and leveling her up.

It was a beautiful cloudless day and the interior looked so lovely with the sun coming through the windows. The scene will be even lovelier, and I’ll post photos of it, when I get the bird crap and construction dust off the windows.

This is the stuff!

It even has the bluish tint of skim milk. But I’m pretty sure is isn’t.

The instructions said it could also be sprayed or rolled on, but we had paint pads on hand and they worked pretty well.

The first coat going on the first side. Once we finished that we went right back over with the second coat.

The next morning, all dry! It looks to me just like it did before we applied the protectant, which was in fact what I was going for, so huzzah.

And there she is, outside! This is a back side view. The little window is the kitchen window above the stove, back door, big bedroom window. She will eventually lose the “door to nowhere” look with a deck that can be removed or hinged up for moving.

More fast-forward progress…

Winter has slowed down construction a bit, but there has still been lots of progress on Casa Chica that I haven’t been keeping up with in the blog. So!

The house is now physically attached to the trailer. A good thing! I wanted it to be “easily” removable from the trailer in case I want (need) to get a heavier-duty trailer, or to put in on a foundation someday. So I had a local metal-working shop make custom brackets that fit snugly around the trailer frame and screw into the house from underneath. I think we ended up installing about 14 of the brackets around the house.

Sort of related to that, we decided to lower the 6 RV jacks that the house is supported by and see what would happen (we also want to move the trailer out of the shed to finish the roof and get it out into the sunshine for a more pleasant working environment, so removing the jacks wasn’t just an experimental lark). Mike smartly made sure the tires were fully inflated and then we went front to back to front to back, lowering the jacks one turn at a time, and… Nothing happened! Hooray! The trailer springs settled a little of course but they still have plenty of oomph for more weight, and the whole thing hardly even got out of level. Whew. Wasn’t sure what I expected, but I had nightmarish visions…

The roof is installed, except for the ridge vent that will be easier to install once the house is out of the shed. Nothing terribly special here – typical plywood sheathing, tar paper, simple galvanized metal roof panels. Holes had to be cut through the roof for the wood stove chimney and plumbing vent, but other than that I think it was a pretty simple job.

The wood stove is in, mostly, so Mike could line up the hole in the roof and the hole in the floor for the fresh air intake. We’ll need to take it out to put in a metal floor pad that I haven’t had made yet, but technically I could have a fire in it now if I wanted to! (I haven’t.) We’ve been heating it to keep it comfortable for working in with an electric space heater that will serve as my backup heat once the construction is done.

Wiring is all done, and all the interior walls are in except where shower plumbing still needs to be installed once the fixtures arrive. More on fixtures later!

The brackets attaching the house to the trailer.

Tar paper on the roof!

The Kimberly stove installed. Isn’t it beautiful? There will be a wood storage insert on that interior wall behind the stove.

The AC plywood is up on the walls and the interior walls/loft are framed!

And the interior walls and loft of the bathroom are framed…

…and covered in AC plywood. Still some plumbing to do in the shower.

Fast forward progress…

Casa Chica is actually much farther along than what my previous post hinted at, and I can think of no reason to not get caught up lickety split to the present day, so here goes…

We have walls! Four of them. And they’re beautiful. My builder, Mike, is an absolute professional and his favorite part of construction is the framing. As I mentioned previously we’re using 6″ lumber to give plenty of room for insulation. After framing up the walls and nailing them into the floor as in a house on a foundation, we decided to go further with the attachment of walls to deck by using metal ties at several points around the house. I’ve heard tell of other tiny housers doing something similar to help counteract the hurricane force winds when the house is moving down the road. Sounded like it wouldn’t hurt.

I will have two storage lofts – one over the entire bedroom area for storage of seasonal clothes, camping gear, etc., and a smaller one over the bathroom for the fresh water tank and water pump primarily. The loft decks are 2×4 framing. Mike also added a couple of 2×4 rafter ties in the “cathedral” ceiling area in the middle of the house, since the lofts are at both ends and there’s really nothing keeping the walls from spreading in the center.

In an effort to save weight we’re using 3/8-inch exterior plywood as both the exterior wall sheathing and the exterior “finish” – read: no siding. We picked a plywood with a lovely grain to it, and we’re going to do some sort of faux board-and-batten look. Since that’s it for the exterior wall, the house wrap layer went between the framing and the plywood. Vapor barrier was another big research project in the Great Condensation Debate – is tar paper or plastic enough? Should we go with a breathable Tyvek-type wrap? Or do we absolutely need to have a new-fangled “smart” material that blocks moisture when humidity is low and increases permeability when humidity is high? I was surprised by how much variation in opinion there was out there – everything from “vapor barriers don’t work and are a waste of time and money” to “you will regret not spending your whole paycheck on the best thing out there.” In the end I went the middle route with Kimberly Clark BLOCK-IT, mostly because that’s what my local mega hardware store sold (vs. Tyvek). They also had CertainTeed’s MemBrain, the “smart” material, but it was quite expensive and we decided that without overwhelming evidence that it was the absolute way to go it probably wasn’t worth the extra cash.

I got many of my windows and my front door from a fantastic surplus store just down the way a bit and their sister store about an hour away, all in new condition with stickers still stuck. I had to order my bedroom awning windows and the back door new, alas, but in total I probably paid 25% of what I would have had I bought everything new. The surplus stuff doesn’t exactly match in the trim department, either color-wise or material-wise, but a bit of paint should make no one the wiser. All of the doors and windows got installed after the exterior plywood was put on. Now it’s looking like a house!

Since my insulation of choice (see the previous post) doesn’t have a facing that can be stapled to the rafters to keep it in, Mike decided to put up the ceiling before the roof so he could lay the insulation in from the top. The ceiling and walls are 3/8″ interior grade plywood that we will finish as is.

Next, electrical wiring! Weeks and weeks were spent deciding on placement of outlets and switches, and especially on lighting. I think I’ll talk about the lighting decisions in another post. Suffice it to say here that we made enough of the decisions for Mike to be able to wire. Nothing too exciting there – we got our supplies from the local semi-mega hardware store. My dad had a box of Cutler Hammer circuit breakers, so that was the brand of breaker box we chose.

And to (finally) arrive at the current state of affairs – the walls and ceiling have been insulated now that the wiring is in, and the roof sheathing is on. Next: install the metal roof, finish the plumbing and put up the interior walls!

Hooray! The first two walls go up! Bedroom walls.

A twofer photo – framing and house wrap. Taken from the bedroom looking through the living area, kitchen and bathroom at the end. The lack of interior walls looks strange now!

This is what I mean by metal ties that connect the walls to the floor. We put them every few feet around the house, just to make sure everything stays attached should I decide to tow the house down the road.

The rafters going in.

Exterior back of the house. Small kitchen window, back door, large bedroom windows. You can see the grain of the exterior plywood too, which is going to be gorgeous no matter how we decide to finish it (decision yet to be made).

A beautiful ceiling! Taken from the kitchen area, looking towards the church window that will be above the bed. The rafter ties are temporary.

Just a sample of the wiring. Such neat work Mike does. This is looking at the kitchen window above where the stove will be.

The insulated walls, post wiring! Taken from the living area, looking towards the bathroom. The breaker box is on the interior bathroom wall, as you can see there.

Designing for the climate

I live in western Wisconsin. We can get as warm and humid as the Gulf Coast in August and as bitterly cold and snowy and dry as inland Alaska in January (Anchorage has a higher average winter temperature than ours). As I write this, it’s -8F and sunny at 4 pm, with a wind chill of -30F. And I plan to live in my house year-round (though I haven’t written off the possibility of hauling it to Mexico every winter). So…some of the tiny house systems designed for California, say, are not going to work when it’s -20F. Nor is R20 insulation in the floor. Summer is a little easier to deal with: I can get water to the house via hose, collect gray water in barrels and open windows for ventilation.

We have spent by far the most time in the design of this house on making it comfortable and usable and modern-house-like during the winter. And here’s what we came up with:

1. 2×6 walls, 2×8 floors and rafters for more insulation capacity. I wanted to go with a more environmentally-friendly insulation than spray foam or rigid insulation, which meant less R value per inch (there’s always a trad-off that makes the environmental friendliness possibly less friendly). The 6″ walls were easy because we had already decided to chuck the 8.5′ maximum width restriction. We are sticking with the 13.5′ maximum height so I initially balked at the loss of space with the thicker floors and ceilings, but I was convinced by the promise of warmer tootsies in the winter. Of course bigger wood also equals more weight, but we used 1x6s for some of the studs and spaced the floor joists and rafters as wide as we could. I ended up choosing UltraTouch denim insulation. My builder is not entirely happy because the stuff is IMPOSSIBLE to cut (I’ll post a solution if we find one), but he still says he’d rather spend a day sawing away at the denim than picking fiberglass out of his skin, clothes, eyes, lungs, hair, etc. The floors and ceilings are R30 (double that in the raised floor of the center section) and the walls are R21. Ostensibly. The insulation didn’t fluff up as much as expected, so in the floor we were also able to put in an inch of rigid foam (makes up for my previous environmentally friendly trade-off?). That will probably be the case for the ceiling too.

2. Gray water tank in the floor of the bathroom. When researching for our design I found people using gray water tanks, but they were storing them beneath their trailers or in other places that would freeze solid here on the first 0-degree night. Or it was taking up valuable space under a counter somewhere. Our solution? We raised the floor 8″ in the bathroom (like we did the center section of the house) and created a pocket for a 30-gallon tank. So it has ~R30 insulation below it and around it, and I’ll be able to access it through a panel in the floor. I wanted to make sure it could be easily removed if I needed to replace it, or for any other reason. I’ll also open the panel to open the drain valve when I need to pump out the full tank. I chose 30 gallons sort of randomly – I wagged that I’d use about 4 gallons a day on average, and I don’t want to have to drain the tank more than once a week. You can order tanks of all shapes and sizes from www.tankdepot.com (be sure to order a bit in advance – it takes a few weeks). The drain is 2″ PVC with a plug that I’ll open to transfer the gray water to a portable tank in the back of a truck, which I’ll then haul to the local wastewater treatment plant. Voila! Easy on paper, the practice is of course yet to be tested. It of course also remains to be seen how quickly I’ll fill up the tank. If I end up having to pump it every other day it might not be much fun either. I’m not going to have any black water – my toilet will be a Loveable Loo type affair. I lived in a yurt with a bucket toilet for a couple of months and found it to be a very good solution.

3. Fresh water tank in the loft above the bathroom. This tank also needs to be within the insulated envelope, and I was more willing to give up storage space in a less accessible loft than under a counter. I haven’t purchased this tank yet and we haven’t completely figured out how and where it will be filled, but I will have an RV pump (I’m looking at a Flojet Quiet Quad diaphragm pump) and not rely solely on gravity. It will be another 30-gallonish size.

4. Kimberly wood stove for heat. How to heat? Big question. Originally I wanted the house to be off the grid, but the economics didn’t work out. Even so, electrical heat was never a consideration (although I may have a small baseboard heater that I can turn on just high enough to keep my house from freezing if I leave for a day or more). I read a few blogs that said the Dickinson propane stove so beloved in many tiny homes isn’t really up to the job of “real” winters. Kerosene is stinky. I was initially opposed to wood heat – a lot of work to gather and haul wood, it has to be practically in the center of the room to meet clearance requirements, constant cleaning up of wood dust and detritus, black soot all over hands and clothes if I get within 6 inches of the stove, having to get out of my cozy bed every three hours to stoke it, heavy, etc – but then I found the Kimberly. It’s expensive, yes, and I’ll still have to gather and haul wood, but it’s super efficient and can purportedly burn for 8 hours. It’s also lightweight and doesn’t require much for clearance from walls. I’m also not as worried about heating myself right out of the house as I would be with a traditional cast iron stove. I’m super excited to try it out.

5. Active exhaust and passive make-up ventilation. I’ve been kept awake at night after reading horror stories of tiny houses and condensation. There’s very little out there about exhausting air from or providing make-up air to tiny spaces. I looked into HRVs (one tiny house builder in Quebec that I corresponded with installed the Lunos e2, which is supposedly sized right for a tiny house) but they’re expensive and my builder wasn’t convinced that we needed to go that far with it. Heating with wood will dry the air, but will it be enough? After much researching, hemming and hawing we’re going with a bathroom fan (Panasonic WhisperFit), a stove hood (Broan Allure) and a passive air inlet (Therma-Stor Fresh 100). The Kimberly stove has its own fresh air inlet, but it’s contained within the stove. I really hope this works, and I’ll probably find out next winter. If it doesn’t, we might be re-thinking that HRV as Plan B. Either way, I’ll post how things are going. That goes for all of these experiments in tiny house winter living.

Our pile o’ insulation. I had to order it, and when I went to pick it up at the mega hardware store 30 minutes away I thought I’d be able to fit it all in the back of my pickup. Nope. 2 trips with a trailer later…

Insulation going into the floor. Note again the raised center section, which provides cover over the wheel wells and adds a little design interest inside the house to avoid the long, mobile home feel.

Here you can see the layer of rigid foam we were able to add over the denim insulation. And a better view of the wheel wells.

The gray water tank in the floor, before attaching the plumbing. It sits above 8″ worth of insulation.

The gray water tank with plumbing installed. The bathroom sink, kitchen sink and shower will drain into it.

From infatuation at first sight… to floor!

I’ve been in love with the idea of tiny houses since my mom showed me a newspaper article with Jay Shafer and his original Epu about a dozen years ago. I pored over Tumbleweed floor plans on the website, trying to decide which one was perfect for me. I got absolutely giddy over tiny appliances, tiny sinks, tiny spice jars. I cheered as the tiny house movement grew and more people chose to resist the pull (or push?) to keep up with the Joneses in the 5,000-sf monstrosity next door. In short, just thinking about tiny houses made me happy. But I wasn’t entirely sure what I would DO with one. Did I need a guest house? A vacation home? I had a 12-acre farm with a cozy, almost-completely-renovated 1,000-sf home and a fantastic 4-stall barn with indoor riding arena. I have always wanted a farm, and I loved mine! Until… I started adding up what owning it was costing me, both in money and in time, and all I could see ahead was a terrific “get into debt” plan. And it wasn’t always fun doing a lot of the work by myself, or having to call on my generous (but long-suffering) parents to give up another of their Saturdays to help me with some project or other. So… then comes November 5, 2011. I’m doing my daily meditation practice when the answer comes, so clearly and rightly that I haven’t questioned it since: Sell The Farm, Build the Little House. Whoa. The farm is on the market two months later.

Fast forward about 15 months (ugh to the housing market downturn), and the farm is no longer mine. The little house, by now already dubbed “Casa Chica” by the Design Team (me, my designer friend and my builder friend), is still very vaguely on paper, so I’m housesitting around. My stuff has been widely dispersed to relatives, Goodwill, Craigslist buyers, etc. and everything I own is in about 20 plastic bins in my parents’ basement. Fast forward again to now, and after about six housesitting gigs and a two-month stint in a yurt I’m still in much the same situation. Except! I’m renting a room at a friend’s house, and Casa Chica is no longer a figment of my imagination (and Sketchup)! It Is Begun.

The Casa Chica design started as a Tumbleweed knock-off, especially after the Design Team attended a Tumbleweed workshop in Madison, WI. After several iterations, we settled on a design influenced heavily by the Tall Man’s Tiny House without the bump-in entry, dormer or sleeping loft (I want to be able to stand up in my bedroom). We also decided to throw maximum road width to the wind and have made it 10 feet wide. It’s 27 feet long, mostly because that was the length of the used trailer I found on Craigslist.

I’ll add posts later about other design and material decisions that have been made, especially as they relate to designing for the cold winters here in western Wisconsin. I’ve found only a handful of people who are planning to live year-round in their tiny house in similar conditions, and I’ve learned a lot from what they’ve shared. I want to add to that body of information, and I plan to keep posting after I’ve moved in about what works and what doesn’t. But for now: there’s a floor!

The trailer, before painting. Yes, it’s an old RV chassis and therefore probably not adequate for long-distance hauling of a 10′-wide house. But it will serve as a fine foundation, and we’re connecting the house to the trailer such that it is easy to detach the house and replace the trailer.

Construction begins!

The bottom, upside down before it got flipped. We opted not to do the fairly popular layer of sheet metal. This trailer really isn’t going to move much.

We’re building around the wheel wells rather than over them. The center section is double thick, so insulation over the wheel well area won’t be a problem.

The deck also makes a nice onion drying surface!

The deck, just prior to nailing on the plywood subfloor. You can kind of see that the center section and farthest section (the bathroom) are raised. More on that later.

The trailer, before painting. Yes, it’s an old RV chassis and therefore probably not adequate for long-distance hauling of a 10′-wide house. But it will serve as a fine foundation, and we’re connecting the house to the trailer such that it is easy to detach the house and replace the trailer.

Construction begins!

The bottom, upside down before it got flipped. We opted not to do the fairly popular layer of sheet metal. This trailer really isn’t going to move much.

We’re building around the wheel wells rather than over them. The center section is double thick, so insulation over the wheel well area won’t be a problem.

The deck also makes a nice onion drying surface!

The deck, just prior to nailing on the plywood subfloor. You can kind of see that the center section and farthest section (the bathroom) are raised. More on that later.